Procedures for preparing metallic specimens for submission to optical microscopy

Autores

  • Natanael Oliveira da Vera Instituto Federal do Piauí
  • Idlla Holanda Pessoa Pio Instituto Federal do Piauí
  • Fernanda da Barbosa da Luz Instituto Federal do Piauí
  • Ayrton de Sá Brandim Instituto Federal do Piauí
  • Rodolpho Carvalho Leite Instituto Federal do Piauí

DOI:

https://doi.org/10.53660/CONJ-934-K05

Palavras-chave:

Metallic specimen preparation, Microscopy, Preparation techniques for microscopy

Resumo

Microscopy analyzes are very important for metallography, they serve to reveal the microstructural constituents, the distribution of present phases and other important properties to characterize the materials. It is important that the specimens follow a rigorous preparation process to ensure that they are free from defects that could compromise the results of the characterization. The work presents the stages of preparation of specimens for optical microscopy. Works related to the research proposal were analyzed in literature texts and thus it was possible to identify the most common and effective practices in the preparation phase of metallic samples.

Downloads

Não há dados estatísticos.

Referências

ABNT. NBR 13284: Preparação de corpos-de-prova para análise metalográfica. Rio de Janeiro: Associação Brasileira de Normas Técnicas, 1995.

ABNT. NBR 15454: Metalografia das ligas de ferro-carbono - Terminologia. Rio de Janeiro: Associação Brasileira de Normas Técnicas, 2007.

AGUIAR, M. A. S. DE et al. Metalografia qualitativa e quantitativa de grãos de austenita prévia de aços de alta resistência e baixa liga. V Congresso Nacional de Engenharia Mecânica. Anais...Salvador: ABCM, 2008.

ALIYA, D.; ANALYTICAL, A. Metallographic Sectioning and Specimen Extraction. Metallography and Microstructures, v. 9, p. 229–241, 2018.

AMBADEKAR, P. K.; CHOUDHARI, C. S. Measurement of Tungsten Carbide Tool Wear by Tribological Investigations. Journal of Bio- and Tribo-Corrosion, v. 6, n. 2, p. 1–6, 2020.

APOLLO et al. Development of polishing machine for preparation metallographic specimen with re-manufacturing. IOP Conference Series: Materials Science and Engineering, v. 885, n. 1, p. 0–5, 2020.

ASM INTERNATIONAL. ASM Handbook Vol. 9: Materials Characterization. 10. ed. [s.l.] ASM International, 1992.

ASM INTERNATIONAL. Metals Handbook, Volume 2: Heat Treating, Cleaning and Finishing. 8. ed. ASM International, 1964. v. 2

ASTM INTERNATIONAL. E3-11: Standard Guide for Preparation of Metallographic Specimens. West Conshohocken, PA: ASTM International, 2011.

BAEKELAND, L. H. The synthesis, constitution, and uses of Bakelite. The journal of Industrial and Egineering Chemistry, v. 1, p. 149–161, 1909.

CALLISTER, W. D.; RETHVISCH, D. Ciência e Engenharia de Materiais. 9. ed. Rio de Janeiro: LTC, 2016.

CARDOSO, G. D. S.; DIAS, V. W.; ROCHA, A. D. S. Os efeitos do processo de corte cisalhante em barras oriundas do processo de trefilação combinada. Revista Materia, v. 22, n. 3, 2017.

CHIAVERINI, V. Tecnologia Mecânica: processos de fabricação e tratamento - Vol. 3. 2. ed. São Paulo: McGraw-Hill, 1986a.

CHIAVERINI, V. Tecnologia mecânica: Estrutura e Propriedades das Ligas Metálicas. 2. ed. São Paulo: McGraw-Hill, 1986b. v. 1

CLAMPS, M. Mounting of Specimens. Metallography and Microstructures, v. 9, p. 242–256, 2018.

COLPAERT, H. Metalografia dos produtos siderúrgicos comuns. 4. ed. São Paulo: Editora Blucher, 2008.

EQUIPMENT, P. P.; WEIGHTS, F. L. Metallographic Laboratory Safety 1. v. 99, n. Reapproved 2005, p. 1–7, 2010.

FEDOROV, S.; SHARIPOV, J.; ABROROV, A. Increasing the surface stability of the cutting tool through complex machining. Journal of Physics: Conference Series, v. 1889, n. 2, 2021.

FISCHER, U. (ED.). Tabellenbuch Metall: ohne Formelsammlung. 44., neu bearb. Aufl ed. Haan-Gruiten: Verl. Europa-Lehrmittel, 2008.

FONSECA, M. G. et al. Redução do percentual de austenita retida pelo processo de shot peening. Matéria (Rio de Janeiro), v. 26, n. 2, p. e12985, 2021.

FREITAS, B. M. DE et al. Microestrutura e microdureza do aço SAE 1020 em diferentes tratamentos térmicos. Congresso Técnico Científico da Engenharia e da Agronomia. Anais... Em: CONTECC 2016. Foz do Iguaço: 2016.

GEELS, K. et al. Metallographic and Materialographic Specimen Preparation, Light Microscopy, Image Analysis and Hardness Testing. West Conshohocken: ASTM International, 2007.

GLUKHOV, L. M. et al. Effective laser technology for making metal products and tools. Metallurgist, v. 60, n. 3–4, p. 306–312, 2016.

GOKHALE, A. M. Quantitative Characterization and Representation of Global Microstructural Geometry. Metallography and Microstructures, v. 9, p. 428–447, 2018.

HADAD, M.; EBRAHIMI, S. M.; ARAEE, A. Experimental and numerical investigation of the effects of preheating temperature on cutting force, chip shape and surface roughness in hot turning of AISI630 hardened stainless steel. Energy Equipment and Systems, v. 9, n. 2, p. 145–158, 2021.

HAN, Y. et al. Combined milling of electrical discharge ablation machining and electrochemical machining. International Journal of Advanced Manufacturing Technology, v. 112, n. 9–10, p. 2889–2897, 2021.

HOGUE, F. Microfractography and Metallography for Failure Analysis. Failure Analysis and Prevention, v. 11, n. d, p. 92–104, 2021.

LEITE, S. S. et al. ENSAIO DE TRAÇÃO E METALOGRAFIA DO AÇO SAE 1020. Revista Engenharia em Ação UniToledo, v. 2, n. 1, 2017.

LENDA, O. BEN et al. Structural and Mechanical Characteristics of AISI 420 Stainless Steel After Annealing. Strength of Materials, v. 52, n. 1, p. 71–80, 2020.

LLANTO, J. M. et al. Recent progress trend on abrasive waterjet cutting of metallic materials: A review. Applied Sciences (Switzerland), v. 11, n. 8, 2021.

MALISKA, A. Preparação de amostras para análise microestrutural. Florianópolis: Universidade Federal de Santa Catarina – UFSC, 2003.

NORTON, R. L. Projeto de Máquinas: uma abordagem integrada. 4. ed. Porto Alegre: Bookman, 2013.

RODRIGUES, L. M. et al. Estudo da microestrutura e da microdureza dos aços 1020 e 1060. Cadernos UniFOA, v. 1, n. 2, p. 39–44, 2014.

ROHDE, R. A. Metalografia preparação de amostras. 3. ed. Rio Grande do Sul: Universidade Regional Integrada do alto Uruguai e Missões, 2010. p. 30

SAMUELS, L. E. Metallographic Polishing by Mechanical Methods. 4. ed. [s.l.] ASM International, 2003.

SCOTT, D. A. Metallography and Microstructure of Ancient and Historic Metals. 1. ed. Singapure: The J. Paul Getty Trus, 1991.

STEPHENSON, D. A.; AGAPIOU, J. S. Metal Cutting Theory and Practice. 3. ed. Boca Raton: CRC Press, 2016.

VOORT, G. F. VANDER. Applied Metallography. 1. ed. New York: Van Nostrand Rfinhold Company Inc, 1987.

VOORT, G. F. VANDER. Metallography: An Introduction. Metallography and Microstructures, v. 9, n. c, p. 3–20, 2018a.

VOORT, G. F. VANDER. Tables of Chemicals and Etchants. Metallography and Microstructures, v. 9, p. 1094–1114, 2018b.

WANG, B. et al. Advancements in material removal mechanism and surface integrity of high speed metal cutting: A review. International Journal of Machine Tools and Manufacture, v. 166, n. May 2021, p. 103744, 2021.

WARREN, A. D. et al. Preparation of Stainless Steel Surfaces for Scanning Probe Microscopy. Microscopy Today, v. 24, n. 3, p. 52–55, 2016.

WETZIG, A. et al. Fast laser cutting of thin metal. Procedia Manufacturing, v. 29, p. 369–374, 2019.

ZIPPERIAN, D. C. Metallographic Specimen Preparation Basics. Pace Technologies, p. 18, 2009.

Downloads

Publicado

2022-04-28

Como Citar

Oliveira da Vera, N., Holanda Pessoa Pio, I., da Barbosa da Luz, F., de Sá Brandim, A., & Carvalho Leite, R. (2022). Procedures for preparing metallic specimens for submission to optical microscopy. Conjecturas, 22(5), 93–109. https://doi.org/10.53660/CONJ-934-K05

Edição

v. 22 n. 5 (2022): mai./jun. 2022

Seção

Artigos

Licença

Copyright (c) 2022 Conjecturas

Creative Commons License
Este trabalho está licenciado sob uma licença Creative Commons Attribution 4.0 International License.